PROFI CONSULTING
from 9am to 5pm
No products
*336 971
DINITROL 6110 Megafill Spray is an acrylic spray filler with higher filling capacity. It levels out more pronounced unevenness and prepares the surface for painting. Fills more than a standard spray filler – copes with more noticeable surface defects, touch-dry in 20–30 minutes – just 10 minutes in a booth at 60 °C, no sanding needed in a thin coat – use it as a primer and paint straight away.
New product
RS-13088
4046085130887
Add to wishlist In your list · view

DINITROL 6110 one-component filler 400 ml
DINITROL 6110 Megafill Spray is an acrylic spray filler with higher filling capacity. It levels out more pronounced unevenness and prepares the surface for painting. Fills more than a standard spray filler – copes with more noticeable surface defects, touch-dry in 20–30 minutes – just 10 minutes in a booth at 60 °C, no sanding needed in a thin coat – use it as a primer and paint straight away.
Send the question to the owner of the store, about this product.
* Required fields
or Cancel

DINITROL 6110 one-component filler 400 ml
To be informed about product update via email, fill out the form.
* Required
or Cancel
DINITROL 6110 Megafill Spray is an acrylic spray filler with higher filling capacity. It levels out more pronounced unevenness and prepares the surface for painting. Fills more than a standard spray filler – copes with more noticeable surface defects, touch-dry in 20–30 minutes – just 10 minutes in a booth at 60 °C, no sanding needed in a thin coat – use it as a primer and paint straight away.
DINITROL 6110 Megafill Spray is an acrylic resin-based filler in an aerosol can. It levels out scratches, scuffs and minor paint damage and creates a smooth base for a new coat of paint.
Compared with a standard spray filler it fills more unevenness, so you can also use it where the surface still needs levelling before painting — for example on areas sanded through to the substrate or after sanding body filler.
The filler is touch-dry after just 20–30 minutes, depending on temperature, humidity and film thickness. At 60 °C in a drying booth, 10 minutes is enough. It can be worked further after approximately 25 minutes.
What you will need
Mask off the area around the repair with materials from the masking category, and you will find degreasing products in the surface preparation category.
Work in a well-ventilated area wearing a respirator, safety glasses and gloves.
Once dry, sand the filler and paint over it. If you applied it in a thin coat as a primer, no sanding is needed before painting.
It is compatible with most refinish paints. You will find more fillers and primers in the fillers and primers category, and paints in the paints and special sprays category.
6110 Megafill or 6100 Sprayfill?
6110 Megafill — higher filling capacity. Choose it when the surface still needs levelling before painting.
6100 Sprayfill — for fine scratches and small defects on a substrate that is already fairly smooth.
Product type spray filler
Filling capacity higher
Base acrylic resin
Colour grey
Volume 400 ml
Density 0.82 g/cm³
Spraying distance 20–30 cm
Touch-dry 20–30 minutes
Drying at 60 °C 10 minutes
Further processing after approximately 25 minutes (20 °C)
Propellant propane/butane
Shelf life 12 months at 15–25 °C
The filling capacity. 6110 Megafill fills more unevenness, so choose it when the surface still needs levelling before painting. 6100 Sprayfill is sufficient for fine scratches and small defects on a surface that is already fairly smooth.
With a full coat, yes — sand it once dry and then paint. If you used it in a thin coat as a primer, you do not need to sand before painting.
After each use, turn the can upside down and spray briefly until only clean gas comes out. This blows the nozzle clear so it will not be blocked for the next repair.
Yes. At 60 °C in a drying booth the filler is dry after just 10 minutes instead of 20–30 minutes at room temperature.
Safety Information (CLP)
Signal word: Danger
Hazard classification:
Aerosol 1
Eye Irrit. 2
STOT SE 3
Hazard statements:
H222 Extremely flammable aerosol.
H229 Pressurised container: May burst if heated.
H319 Causes serious eye irritation.
H336 May cause drowsiness or dizziness.
EUH208 Contains butyl acrylate. May produce an allergic reaction.
Contains: n-butyl acetate, ethyl acetate, acetone, butan-1-ol
Precautionary statements:
P210 Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.
P211 Do not spray on an open flame or other ignition source.
P251 Do not pierce or burn, even after use.
P280 Wear protective gloves/eye protection/face protection.
P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
P337+P313 If eye irritation persists: Get medical advice/attention.
P410+P412 Protect from sunlight. Do not expose to temperatures exceeding 50 °C.
This discussion is especially meant for information exchange between customers. For questions regarding your order or stock availability, please contact us directly.
No manufacturer found
