Brake pads CL Brakes 4041RC6

RC6 - Snow, wet, gravel races or rear axle

Average friction coefficient µ= 0,4.
CL brakes original compound, RC6 was designed to apply to a wide range of motorsports, from rally to circuit. It has a high and very flat friction level and can be used successfully in almost every type of race car. Low compressibility provides a stiff pedal which greatly increases feedback and allows for easier modulation. It can also be used in the front or rear axle combined with the RC8 or RC5 to adjust bias.

Application:

ALFA ROMEO 145 , 2.0 Twin Spark 16V 96→99 (front pads)

ALFA ROMEO 146 , 2.0 Twin Spark 16V 96→99 (front pads)

ALFA ROMEO 147 , 2.0 16V 00-→ (front pads)

ALFA ROMEO 155 , 2.0 Quadrifoglio 4 Turbo 16V 95→96 (front pads)

ALFA ROMEO 155 , 2.0 Quadrifoglio 4 Turbo 16V 95→96 (front pads)

ALFA ROMEO 155 , 2.0 Turbo (167) 92→97 (front pads)

ALFA ROMEO 155 , 2.0 Twin Spark 16V 95→97 (front pads)

ALFA ROMEO 155 , 2.0 Twin Spark 16V 95→97 (front pads)

ALFA ROMEO 155 , 2.5 V6 95→97 (front pads)

ALFA ROMEO 155 , 2.5 V6 95→97 (front pads)

ALFA ROMEO 156 , 2.0 97→02 (front pads)

ALFA ROMEO 156 , 2.5 97→02 (front pads)

ALFA ROMEO GTV, 2.0 V6 Turbo 95-→ (front pads)

ALFA ROMEO GTV , 2.0 16V 95→04 (front pads)

ALFA ROMEO Spider , (916) 2.0 Turbo V6 98-→ (front pads)

ALFA ROMEO Spider , (916) Convertible JTS 03→04 (front pads)

FIAT Bravo , (182) 2.0 HGT 20V 95→01 (front pads)

FIAT Bravo , (198) 1.4 -- (front pads)

FIAT Coupe , 2.0 Turbo 16V 95→03 (front pads)

FIAT Coupe , 2.0 Turbo 20V 97-→ (front pads)

FIAT Punto , HGT -- (front pads)

LANCIA Dedra , 2.0 HF Integrale 94→97 (front pads)

LANCIA Dedra , 2.0 HF Integrale Turbo 94→98 (front pads)

LANCIA Dedra , 2.0 HF Integrale Turbo 98-→ (front pads)

LANCIA Delta , 1.8 GT 16V 96→98 (front pads)

LANCIA Delta , 1.8 LE 96→98 (front pads)

LANCIA Delta, 1.8 LX 96→98 (front pads)

CL Brakes (previously Carbone Lorraine) created in 1919, roup is the main actor in integrated on-board railway systems with more than 4500 employees and more than 30 sites over the world. Now called "Faiveley Transport Gennevilliers" and owner of the brand CL BRAKES, the Brake Pads Department retains the manufacturing activity for its sintered metal brake pads in its historical site of Gennevilliers, France, benefiting from a common know-how in R&D acquired in aeronautic as well as in rail activities, and thus allowing a constant improvement of our materials for cars, motorcycles and mountain bikes. Sintered metal brake pads are made based on powders. The friction product contains at least ten ingredients (Bronze, ceramics, graphites...). Each of these ingredients makes the friction mixture, which is then compressed in a device that will give it its final shape. The obtained item is then positionned on its metal support and then heated in a 900+°C oven. It's the sintering process : a constituent of the product melts, consolidates the material and makes it fuse with its support. The brake pad is then rectified, checked and packed.