PROFI CONSULTING
from 9am to 5pm
No products
*287 250
FORGE Motorsport - This Forge intake kit is for the VW Up 1.0 TSI and GTIThis intake kit includes a bespoke aluminium housing, powder coated black for that OEM look and for a hard wearing finish.
New product
FMTIA3
Turbo Inlet Adaptor for VAG 1.0 TSI Engine
FORGE Motorsport - This Forge intake kit is for the VW Up 1.0 TSI and GTIThis intake kit includes a bespoke aluminium housing, powder coated black for that OEM look and for a hard wearing finish.
Pošlite obsluhe obchodu otázku k tomuto produktu.
* povinný údaj
alebo Zrušiť
Turbo Inlet Adaptor for VAG 1.0 TSI Engine
To be informed about product update via email, fill out the form.
* Required
or Cancel
FORGE Motorsport - This Forge intake kit is for the VW Up 1.0 TSI and GTIThis intake kit includes a bespoke aluminium housing, powder coated black for that OEM look and for a hard wearing finish.
The OEM plastic turbo inlet includes a restrictive ribbed and hollow noise chamber that is designed to disturb the air flow and reduce induction noise, this OEM part has a detrimental effect to the engines performance especially when tuned. For the best possible gains, the chamber was removed allowing for the increase of the volume and air flow significantly. FORGE design also has an internal stepped area where it is positioned and joined to the turbo housing, this is to ensure the transition is as smooth as possible from the inlet tract to the turbo.
Several different designs and material choices were tested. The construction of FMTIA3 is manufactured from reinforced multi ply silicone which is more durable than the OEM plastic pipe and it will also not suffer from heat soak like other similar products. With its enlarged capacity and less restrictive surface area it routes air directly into your turbo charger and allows a greater volume of air to be compressed, this can have a positive effect on accelerating your vehicle after long deceleration or in between gear changes due to more air being kept within the inlet tract to the turbo charger.
One significant feature of FMTIA3 is its compatibility with vehicles equipped with and without the PCV system integrated into the existing turbo intake, the early engines do not have the breather system in place from the fuel tank to the elbow. We supply the necessary hardware to blank of the elbow spouts if its required to fit the turbo inlet adaptor to the earlier engine revision.
The one way valve and coupler adaptor are also supplied so the elbow can be installed to the newer revised engine. The FMTIA3 is also compatible with the factory air box, however for the best performance results we recommend using FORGE intake systems for your particular chassis application.
This is a product which is essential when tuning the 1.0 TSI engine, if its either stage one or stage two tuning we have seen consistent gains from 3-5 bhp depending on the vehicles state of tune.
This is a straightforward yet very effective power increasing modification that can be fitted with basic tools and has a typical installation time of around 60 minutes. As with all Forge products it includes a full set of comprehensive installation instructions to make fitting as straightforward as possible.
Application:
Audi
-A1 (8X) 2010-2018 1.0 TSI
-A3 1.0TSI
Seat
-Arona 1.0 TSI
-Ibiza Mk5 (KJ) 2017 - late 2021 1.0 TSI
-Leon Mk3 2012-2020 1.0 TSI 2015-2020
-Toledo 1.0 TSI
Skoda
-Fabia 1.0 TSI
-Rapid 1.0 TSI
Volkswagen
-Golf MK7 1.0 TSI
-Golf MK7.5 1.0 TSI
-Polo 1.0 TSI
-T-Roc 1.0 116PS
-Up 1.0 GTI/TSI
This discussion is especially meant for information exchange between customers. For questions regarding your order or stock availability, please contact us directly.
FORGE Motorsport - This Forge intake...